[Xerte] use of isFunc and passing of parameters

[Dave Burnett]

OK, found it.

In the handleClick scripts add this middle line:

pageName = hsData.hotspot[icon.parentNode.index()].destination;
args[0] = pageName; //added
navToPage(pageName);




----------------------------------------
> Date: Mon, 19 Apr 2010 23:46:07 +0100
> From: johnathan.kemp at ntlworld.com
> To: d_b_burnett at hotmail.com
> Subject: RE: [Xerte] use of isFunc and passing of parameters
> CC: xerte at lists.nottingham.ac.uk
>
> I have attached a zipped up sample xerte project.
>
> If you unzip it and open it in Xerte you will be able to see what I am referring to.
>
> The use of href="asfunction:_level0.engine.navToPage,destPageName", appears to be setting the value of args[0] such that the value of the passed parameter when using navToPage(pageName) is ignored.
>
> The only solution I have found is to set args[0] in the script that calls the function and then to pass args[0] as the parameter, e.g.
>
> args[0] = hsData.hotspot[icon.parentNode.index()].destination;
> navToPage(args[0]);
>
> This does not feel right. I don't understand what it is that the hyperlink approach is doing that is affecting the receipt of the passed parameter.
>
> Any ideas would be most welcome.
>
> Kind regards
>
> Johnathan
>
> ---- Dave Burnett  wrote:
>>
>>
>> Do you have a sample file I could take a peek at?
>>
>> Dave
>>
>> ----------------------------------------
>>> Date: Sun, 18 Apr 2010 22:33:38 +0100
>>> From: johnathan.kemp at ntlworld.com
>>> To: xerte at lists.nottingham.ac.uk
>>> Subject: Re: [Xerte] use of isFunc and passing of parameters
>>>
>>> Just to clarify my first posting.
>>>
>>> I originally tested the second method, that of calling the function from a script e.g. navToPage(parameter1,parameter2,parameter3), but found that only parameter 1 was passed through to the function as args[0]. args[1] and args[2] were undefined. However this still left me with the situation where if I had two wizards.
>>>
>>> The routed hotspot wizard that called the function from a script using navToPage(destPageName)
>>>
>>> and
>>>
>>> The routed text wizard that called the function using href="asfunction:_level0.engine.navToPage,destPageName"
>>>
>>> Pages created with the routed hotspot wizard work fine until a page based on the routed text wizard is used to redirect the user to a page based on the routed hotspot wizard. At which point the args[0] from the routed text page appears to persist so that the routed hotspot page effectively redirects to itself, rather than the page name passed to it.
>>>
>>> The only solution appears to redefine args[0] to the destination page and then call navToPage(destPageName)
>>>
>>> I hope this makes things a bit clearer.
>>>
>>> Any ideas as to what is happening here and how to modify things so that the parameter is passed correctly, without the work around would be much appreciated.
>>>
>>> Kind regards
>>>
>>> Johnathan
>>>
>>> ---- johnathan.kemp at ntlworld.com wrote:
>>>> I am developing a couple of page wizards, both of which provide the capability to define exit points from the page.
>>>>
>>>> The first is a text page that allows you to define hyperlinks to other pages in the project. This is supported by a script where isFunc = 1.
>>>>
>>>> I am calling it with
>>>>
>>>> Routed Tab.
>>>>
>>>> The destination page name, in this case rtFinal, is received as args[0] in the script navToPage. It appears only possible to pass one parameter.
>>>>
>>>> I have a second wizard based on the hotspot in which any hotspot can have a destination page assigned to it. I have a similar function script in this wizard which is called by the script that runs when the hotspot is clicked on.
>>>>
>>>> This script calls the function by navToPage(parameter1,parameter2,parameter3)
>>>> The results are received by the script in args[0],args[1],args[2]
>>>>
>>>> All has worked well when the pages work in isolation, but once the text page has been run this then appears to define the args array at a level that dominates over the hotspot page. The only way I can get this to work is if I set args[0] before I call the function and then pass args[0] as a parameter, otherwise it picks up the value of args[0] set by the text page.
>>>>
>>>> Can anyone shed any light on what is going on here?
>>>> Do I need to declare a new array args at the start of every page?
>>>> How would you operate two functions in a page if every function is going to handle its parameters as the same array args[]?
>>>>
>>>> Kind regards
>>>>
>>>> Johnathan
>>>> _______________________________________________
>>>> Xerte mailing list
>>>> Xerte at lists.nottingham.ac.uk
>>>> http://lists.nottingham.ac.uk/mailman/listinfo/xerte
>>>
>>> _______________________________________________
>>> Xerte mailing list
>>> Xerte at lists.nottingham.ac.uk
>>> http://lists.nottingham.ac.uk/mailman/listinfo/xerte
>>
>> _________________________________________________________________
>> The New Busy is not the too busy. Combine all your e-mail accounts with Hotmail.
>> http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4
 		 	   		  
_________________________________________________________________
Hotmail has tools for the New Busy. Search, chat and e-mail from your inbox.
http://www.windowslive.com/campaign/thenewbusy?ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_1